Your Complete Instruction for Bathtub Installation
Your Complete Instruction for Bathtub Installation
Blog Article
Just how do you actually feel when it comes to A Step-by-Step Guide to Installing a Bathtub?
:max_bytes(150000):strip_icc()/adhesive-type-tub-and-shower-surround-2718959-hero-22d394dc48de474a988eeaad88e9d7b0.jpg)
Setting up a bath tub isn't exactly rocket science, however it does need strong plumbing, woodworking, and in some cases, tiling skills. Replacing an old tub with a new one is likewise a reasonably tough job. If the old bathtub is easily obtainable, the task can relocate immediately; if you need to open a wall to remove the old bathtub and also place the new bathtub, the job is a lot harder. In either situation, the project is within a residence handyman's abilities, although you will require a helper to move out the old bathtub as well as embeded in the new one. Make sure you have actually qualified on your own for the job and also are comfortable trying it. Instead of working with a specialist to take over a halfway-completed project, it is far better to consider utilizing one prior to you begin. Possibilities are you might require a professional plumber to make tube connections.
This write-up will certainly help you set up a brand-new tub in your restroom if you have actually already gotten a new tub as well as do not need to change the plan of your previous water system pipelines.
Your devices and also product list must make up the following:
Removing Old Touches
If you require to replace old faucets with brand-new ones as a part of your installation, after that the first thing you must do is disconnect the water supply. After doing so, activate the taps to drain pipes any water continuing to be in the system. The process of getting rid of the existing taps can be fairly troublesome as a result of the restricted access that is commonly the case.
Utilize a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that attaches the supply pipes to the taps. Have a fabric all set for the remaining water that will come from the pipes. As soon as the supply pipelines have actually been gotten rid of, use the same tool to loosen the nut that holds the taps onto the bath/basin. You will need to quit the solitary taps from turning during this procedure. When the faucets have actually been removed, the holes in the bath/basin will have to be cleaned up of any old sealing compound.
Before moving on to fit the brand-new faucets, compare the pipe links on the old taps to the new faucets. If the old taps are longer than the brand-new faucets, then a shank adapter is needed for the new faucets to fit.
Fitting New Touches
If the tails of the new faucets are plastic, then you will certainly need a plastic adapter to avoid damage to the string. One end of the connector fits on the plastic tail of the tap and also the other end gives a connection to the existing supply pipelines.
If you need to fit a monobloc, then you will certainly require minimizing couplers, which attaches the 10mm pipeline of the monobloc to the typical 15mm supply pipe.
Next, position the tap in the installing opening in the bath/basin ensuring that the washers remain in area in between the tap and the sink. Secure the tap in position with the supplier offered backnut. When the tap is securely in place, the supply pipes can be connected to the tails of the taps. The taps can either be attached by using corrugated copper piping or with typical tap adapters. The previous type ought to be connected to the faucet ends initially, tightening up only by hand. The supply pipelines can later on be connected to the various other end. Tighten both ends with a spanner after both ends have actually been linked.
Installing the Bath tub
Utilizing both wooden boards under its feet, position the bathtub in the called for position. The wood boards are valuable in equally spreading the weight of the bath tub over the area of the boards instead of focusing all the weight onto 4 tiny points.
The following objective is to ensure that the tub is leveled all round. This can be accomplished by examining the level and adjusting the feet on the tub up until the level checks out degree.
To mount faucets, fit all-time low of the outermost versatile tap adapter to the suitable supply pipe by making a compression sign up with; after that do the very same for the other faucet.
Activate the water system as well as check all joints as well as new pipework for leaks and also tighten them if essential. Fill up the tub and additionally inspect the overflow electrical outlet as well as the regular outlet for leakages.
Finally, take care of the bathroom paneling as described in the maker's instruction manual. Tiling as well as securing around the bath tub ought to wait up until the bath tub has actually been used a minimum of when as this will certainly resolve it right into its last position.
Getting ready for the Setup
First of all, the sustaining structure provided with the bathroom must be fitted (if called for) according to the supplier's guidelines. Next off, fit the taps or mixer to the tub. When fitting the tap block, it is important to make sure that if the faucet features a plastic washer, it is fitted between the bathroom as well as the taps. On a plastic bathroom, it is likewise practical to fit a sustaining plate under the faucets unit to stop stress on the bathtub.
Fit the versatile faucet connectors to the bottom of both faucets using 2 nuts as well as olives (often supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the electrical outlet through the hole in the bath. Make use of the nut supplied by the supplier to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the adaptable overflow pipeline to the overflow outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bathroom. Make certain you make use of every one of the provided washing machines.
Attach the catch to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Link the bottom of the overflow tube in a similar manner.The bathroom need to currently be ready to be fitted in its last placement.
Tiling Around the Tub
In the location where the bath meets the floor tile, it is essential to seal the joins with a silicone rubber caulking. This is important as the installation can move enough to crack a stiff seal, creating the water to penetrate the wall in between the bathroom as well as the tiling, causing complications with moisture and also feasible leakages to the ceiling listed below.
You can pick from a range of coloured sealers to blend in your fixtures and fittings. They are sold in tubes and also cartridges, and are capable of sealing voids approximately a size of 3mm (1/8 inch). If you have a bigger space to fill up, you can fill it with spins of drenched newspaper or soft rope. Bear in mind to constantly load the bathtub with water before sealing, to enable the activity experienced when the tub is in use. The sealant can split relatively early if you do not think about this motion prior to sealing.
Additionally, ceramic coving or quadrant tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are also conveniently available on the marketplace. It is recommended to fit the tiles utilizing water-resistant or water resistant adhesive and also grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Hopefully you enjoyed reading our excerpt on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround. Thank you for spending some time to browse our article post. If you please set aside a second to promote this entry if you appreciated it. Many thanks for your time. Please check up our site back soon.
Hot water gone? Call. Report this page